11/25/2023 0 Comments Firebird sequential tail lights![]() ![]() They will not work on cars with separate turn signals, or cars with amber lenses. ![]() Installation takes about an hour.Note: Sequential Turn Signals only work on cars with combination brake/turn signal lamps. Want more separation between individual lamps? Just put in a slower flasher!Each kit comes with 2 modules (one for each side of the car), wire, connectors and printed instructions. While other products offer you fixed timing or complicated manual adjustments, our modules sense your car's flasher speed and adjust the 1-2-3 sequence timing for you. This kit is specifically designed to convert the outer tail light bulb to brake/turn/tail light operation without modifying your tail light housing or replacing sockets.These modules feature sophisticated electronics that automatically adjust the sequencing speed to match the turn signal flasher in your car. Many aftermarket kits can not make this claim.The STS-3TA Sequencer Kit will convert the tail lights on your 1993-2002 Firebird or TransAm to sequential operation. This eliminates the chance of water intrusion which can lead to condensation, fogging and corrosion within the tail light housings. In addition, the kits are specifically engineered to not compromise the waterproof sealing of the tail light housings. This provides the vehicle with the absolute brightest and most noticeable tail light function. The panels will often light up areas that the OEM lighting does not illuminate. Unlike many aftermarket LED panels, our panels are specifically designed to utilize all available lighting area available in the tail light lenses. Ignition must be On to provide sequential flashing.Įach CST kit is uniquely engineered for each application. These kits incorporate high efficiency LED lights that increase tail light brightness, reliability and longevity. This allows running illumination and warning flashers when the key is out of the ignition. Pontiac Firebird Sequential LED Taillight Kit 98-02) The Classic Sequential Tail Light (CST) kits are direct retrofit and replacement for incandescent light bulbs in classic vehicles. The exclusive design also allows the tail light panel to perform running light, brake light and emergency flasher functions when the vehicle is not running. ![]() This eliminates unnecessary current draw on the battery that can lead to a dead battery over time. When ignition power is Off, the tail light panels do not draw any power from the vehicle. The selection is stored in memory within the onboard controller so every time vehicle is started, the same pattern is used. Selection is performed while panel is powered up so user can observe each pattern until the desired pattern is determined. Each press of the switch steps panel through each of the available patterns. If sequential lighting patterns are desired, then the attached pink wire must be wired to +12 volt ignition power.Ī pushbutton switch on the back or front of the light panel is used to select from any of the pre-programmed sequential patterns. The simple installation requires a quick mounting of the LED lighting panel to the tail light housing or lens, depending on application and plugging in the wired bulb plug(s) into the factory bulb socket(s). Standard Flash Mode: Flashes all LEDs in all panels together with the flasher relay or solid light with brake, mimics light bulb operationĭemonstration Mode: Steps through each sequential pattern cyclically, flashes each sequence 6 times before stepping to the next sequence, then repeats. Tail Light Operational Functions: Turn Signal Light, Brake Light, Running Light and Emergency Flash (not including demonstration and standard flash modes) Number of Sequential Patterns: 10 > Industry First << For LED lighting to function properly, a Low Current Flasher Module must be installed in place of the traditional turn signal flasher module. ![]() The kit is designed to work with OEM tail light housing and lenses as well as aftermarket components. There is no separate sequential lighting control module to mount and wire up. In addition, the kit includes a self-contained microprocessor and circuitry to enable a multitude of sequential lighting patterns. Second Generation Pontiac Firebird (1970 - 1981) Sequential Tail Light Conversion Kit. This includes low level running light illumination, brake light illumination, turn signal illumination, emergency flash and back-up lighting where applicable. Pontiac Firebird Generation Specific Discussions. The kits replace all the functionality of the light bulbs they replace. The Classic Sequential Tail Light (CST) kits are direct retrofit and replacement for incandescent light bulbs in classic vehicles. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |